• AVLAB-GE03-1
  • AVLAB Dual Port Gigabit Ethernet PCIe Card - I350-T2, 4-Lane, Dual Profile Bracket

■ Quickly adds two independent Gigabit Ethernet ports through an available PCI Express slot to server or desktop systems
■ Intel I350-T2 chipset supports reliable and advanced network connectivity
■ Compliant with IEEE 802.3, 802.3u, 802.3ab with full duplex and Wake-on-LAN support
■ Features innovative power management including Energy Efficient Ethernet (EEE) and DMA Coalescing to increase efficiency and reduce power consumption
■ Fits both standard and low profile system chassis with the included spare low profile bracket

  • $0 $0

產品詳情

Quickly adds two independent Gigabit Ethernet ports
through an available PCI Express slot to server or desktop systems

Intel I350-T2 chipset
supports reliable and advanced network connectivity

Compliant with IEEE 802.3, 802.3u, 802.3ab with full duplex and Wake-on-LAN support

Features innovative power management
including Energy Efficient Ethernet (EEE) and DMA Coalescing to increase efficiency and reduce power consumption

Fits both standard and low profile system chassis
with the included spare low profile bracket

Requirements
Desktop PC with one available PCI Express (PCIe) slot
Windows® 10 (32-/64-bit) / 8.x (32-/64-bit) / 7 (32-/64-bit)
Windows® Server 2016 (32-/64-bit) / 2012 R2 / 2012 (32-/64-bit) / 2008 R2
Linux kernel 2.3.2 and later
Works with Linux but not supported

Package Contents
Dual-Port Gigabit Ethernet PCIe 4-Lane Card - I350-T2
Spare Low profile bracket
Driver CD
Installation guide

產品規格

Chipset: Intel I350-T2

 

Bus connector: PCI Express x4

 

Version: PCI Express 2.1

 

Network transfer rate: 10/100/1000 Mbps

 

Connectors: 2 x 8-pin RJ-45, Female 

 

Product:

■ Dimensions: 5.43" (W) x 0.79" (H) x 4.72" (D)

■ Weight: 0.17 lbs

■ Color: Green

 

Environmental conditions:

■ Operating temperature: 32 to 140 degrees F

■ Storage temperature: 14 to 158 degrees F

■ Relative humidity: 5% to 90% RH (non-condensing)

 

Certifications/Standards: FCC, CE, RoHS

 

Warranty: 1 year limited

 

Country of origin: China

FAQ

  • Why do I have speed or connectivity issues?
  • If you are experiencing speed or connectivity issues, it is best to set a specific speed at half or full duplex in your settings. You can set your network adapter to perform at a certain speed, but the device that the adapter is connected to (whether it is a router, switch, or computer) must also be able to perform at the same speed.

    Note: You must log in as the local administrator before you continue.

    To open Device Manager:
    ■ Press Windows key + R.
    ■ Type devmgmt.msc.
    ■ Click OK.
    ■ Open the Networking adapters section.
    ■ Right-click the network adapter that you want to change and select Properties.
    ■ Click the Advanced tab.
    ■ Scroll down to Speed & Duplex. By default, it is set to Auto-Negotiate.
    ■ Select any of the speeds that you see in the list.
    ■ Click OK and restart your computer.
  • I am having issues with my new network interface card (NIC) and my on-board NIC is still enabled. What do I do in Windows?
  • Sometimes an on-board network interface card (NIC) conflicts with a new NIC. In these cases it is best to disable the on-board NIC.
    The best way to disable your on-board NIC is to go into your BIOS and disable it there if possible. To do this, consult your motherboard manual.
    You can also disable any NIC in Windows.

    Here is how you do this:
    First click Start, or, in Windows 10 and 8, hold down the Windows key and press X. Then click Control Panel.

    Windows 10
    ■ Click Network and Internet.
    ■ Click Network and Sharing Center.
    ■ On the left, click Change adapter settings.
    ■ Right-click the NIC that you would like to disable and select Disable.

    Windows 8
    ■ Click Network and Sharing Center.
    ■ On the left, click Change adapter settings.
    ■ Right-click the NIC that you would like to disable and select Disable.

    Windows 7
    ■ Click Network and Internet.
    ■ Click Network and Sharing Center.
    ■ On the left, click Change adapter settings.
    ■ Right-click the NIC that you would like to disable and select Disable.

    Windows Vista
    ■ Click Network and Sharing Center.
    ■ On the left, click Manage network connections.
    ■ Right-click the NIC that you would like to disable and select Disable.

    Windows XP
    ■ Click Network Connections.
    ■ Right-click the NIC that you would like to disable and select Disable.
  • How do I confirm that Windows detects my LAN device?
  • To confirm that Windows detects your LAN device, complete the following:
    Press the Windows key+R, type devmgmt.msc, and press Enter.
    In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.
    For example, a USB LAN device would be under Universal Serial Bus controllers.

訂閱AVLT獨家產品資訊